-
- 대화정밀공업은 최고 품질의 자재를 생산하기 위해 노력합니다.
- Epoxy Sealant
- Goods View
- DH-400S Dry Type Sealant DH-400WS Wet Type Sealant DH-700 Elastic Type Sealant(Elongation50%) DH-207 High Viscosity Sealant DH-130S Fast hardening Sealant DH-207F High Viscosity & Elasticity Sealant DH-600 Elastic Sealant(Elongation 20%)
-
Epoxy Sealant
DH-130S Fast hardening Sealant
- Price
- inquiry
- Feature & Purpose
- DH-130S is use for emergency repair or winter season on feature of fast hardening and strength
- attached file
- attached file2
DH-130S fast hardening dry sealing material reduces sealing time and injection time. It is designed as crack sealing material for epoxy injection and steel plate reinforcing, and for various other purposes including for the setting of syringe injector. It has an excellent bonding strength with concrete and high crash worthiness.The fully hardened composition does not cause any chemical action on the reinforcing bars or concrete structures, shows no shrinkage after hardening and maintains stable bondage because of little internal stress. Compared to cement mortar or concrete, it has an excellent mechanical strength in all respects including compression strength, bending strength and tensile strength, etc. and can be used as sealing materials for steel plate compression injection because it is highly strong and adhesive and designed to withstand high pressure. Chemicals are not dried while they are agitated and can be easily removed with a hand grinder. It is suitable for application to the vertical surface and ceiling because it does not run down. The excellent adhesive strength of epoxy resin ensures that the hardened composition maintains a sufficient adhesive strength for the cement mortar, concrete and reinforcing bar etc. and does not produce de-lamination from the base member of the structure. Sealing of cracked area for crack repairing, for setting washer and sealing for the reinforcement of steel plate It is designed as a sealing repair product of the cracks without staying power or the joints of concrete structure and plastering mortar. It contributes to the restoration of staying power of the structure by filling(sealing) the large cracks and cut areas with a specially processed epoxy resin of high bonding strength, tensile strength and compression strength. It improves the durability of structures by preventing water leakage from cracks and corrosion of reinforcing bars by the infiltration of harmful gas in the air. Its applications are as follows.
Repair with Reinforce for Crack of Subway & Tunnel Sealing of cracks of dry concrete structure Sealing of gap produced by dry cement plastering mortar and tile etc. Sealing for grouting reinforcement of aged, weakened parts of dry concrete Sealing for grouting repair of cracks on dry concrete molding products DH-130S Dimension Details DH-130S Dimension Details Classification Main Component Hardening Component Remarks Exterior Appearance White Paste Black Paste - Mixing Rate 1 1 Specific Gravity 1.0 ± 0.1 0.99 ± 0.1 23±0.5℃ Pot Life(Min) 20±10 23±0.5℃ Tack Free Time(Hours) 3±1 23±0.5℃ Hardening Time(Hours) 8~12 - Packing Unit 10kg 10kg - DH-130S Property Data DH-130S Property Data Test Category Result Value Base Value Test Method Compression Strength ( N/㎟ ) 71.4 Over 50 KS F 4923 Adhesive Strength ( N/㎟ ) 8.2 Over 6 Seal Breaking Expansion Rate ( % ) 5.2 Under 10 Seal Strength ( N/㎟ ) 31.2 Over 15 Hardening Contraction Rate ( % ) 2.2 Under 3 Heating Change (110±3℃,168hr) Weight Change Rate ( % ) 1.6 Under 5 Volume Change Rate ( % ) 1.3 Under 5
Pot Life the period of time during which you can work without a change in viscosity after resin and hardener are mixed. Tack Free the state of hardening in which you can lightly touch the mixed resin with your hand, but the hardened material does not stick. Hardening Time the time it takes for the mixed resin to be hardened enough to realize about 80% of final mechanical strength.
① Reinjector is a mid-low pressure injecting device, upgraded to improve the effectiveness of grouting for crack repairing by incorporating the merits of the high pressure grouting of packer and the merits of syringe injector.
② Syringe injector is a low-pressure, low-speed grouting device. A syringe injector containing the resin is set on the cracks and the resin is slowly injected with the help of resilience of the rubber band.Treating the surface to be sealed Work process shall be determined by checking in advance the condition, width, depth of cracks. Remove dust or dirt from the area to be sealed with a wire brush and remove dirt from the surface by using a detergent like soap or thinner if any oily substance still remains. By using gas burner, if needed, dry the inside of cracks as much as possible before you start sealing so that you can remove moss or excessive moisture from the inside or surroundings of cracks. In case paint still remains on the area to be sealed,remove it cleanly with a grinder and steel knife. Mixing of Epoxy Resin The most appropriate temperature for mixing is around 10℃~25℃ and you should use flat board suitable for the amount of mixture. In the beginning, you should mix small amount only because pot life varies greatly depending on the ambient temperature and the epoxy resin temperature. Put a proper amount of main material and hardener based on their weight on a flat board. Then Mix DH-130S so taken for 2~3 minutes by using a steel scoop until it shows uniform color. Sealing of cracks Seal the cracks with mixed resin. Do the sealing of cracks, 1mm thick and 30mm wide, and make sure that the epoxy resin does not leak from the cracks. (For the sealing of rugged surface, a rubber scoop will be very helpful for more efficient and smoother work.) Make sure to use all the mixed epoxy resin within pot life. All the equipments and tools that are used for this operation should be cleaned when the operation is finished. Detergent such as M.E.K, Acetone, Xylene, Toluene and epoxy thinner should be used when cleaning. If the Foam is smeared on your skin during the performance, wash it immediately with flowing water.- When you treating medical fluid, make sure you wear protective helmet, goggle clothes and other protective devices.
- If the medical fluid is smeared on your skin, wash it off immediately and clean up with soapy water.
- All the hand tools and equipments that are used for this operation should be cleaned with thinner thoroughly.
- If you are working in sealed room, then make sure to conduct constraint ventilation for clean air.
- If the medical fluid is smeared on your skin and causes skin trouble, then you should go see specialist for prescription.
- If the temperature is below 5℃, then you must artificially raise up the temperature of medical fluid. This way you can get proper Pot Life.
- If the atmosphere temperature is high and the area is humid, Pot Life of medical fluid quickens. On the contrary, Pot Life will slow down in low temperature area.
- Be aware of it before you conduct the operation.Recommended temperature for storage is 10~25℃ with no moisture. Store it in cool area. Storing period is about 6 months in sealed condition however it can be corrupted according to storing area and conditions. Preferably use it as soon as possible.
Main Contents
-
Daehwa Precision
-
Mechanical injection packer
-
concrete crack injection repair
-
concrete repair kits
-
Single component Injection Pump
-
Twin Line Injection Pump
-
Acrylic Injection Pump
-
Grouting Injection Pump
-
grouting injection
-
polyurethane injection system
-
resin injection pump
-
repair of concrete
-
epoxy injections
-
epoxy injection system
-
epoxy injection systems
-
concrete repair epoxy injection
-
Water stop grouting Method
-
Reinjector Injection Method
-
Syringe Injection Method
-
concrete repair epoxy mortar